Category Archives: SFP Transceiver

HP J4860C X121 1G SFP LC ZX SFP Transceiver Module

HP J4860C

Stop wasting time and money from online shops, buy HP J4860C from stock, get HP J4860C SFP from direct factory, saving lots of money and time in contrast to buying from online stores.all the transceivers are 100% compatible, attractive and excellent packing, 100% tested to make sure quality. We produce making in stock the HP J4860C SFP compatible transceivers. We send the HP J4860C SFP from your factory warehouse to worldwide customers by EXPRESS so we make sure the HP J4860C SFP is fully suitable for your system.

HP SFP J4860C General descriptions

This HP compliant J4860C is a 1000BASE-ZX SFP 1550nm 80km transceiver module. The J4860C transceiver module provides a low cost high-performance connection. The J4860C is 100% compatible with all HP series switches and modules which support SFP transceivers.

HP SFP J4860C Features & Specifications

Form Factor: SFP
Device Type: Transceiver module
Interface (Bus) Type: Plug-in module
Connectivity Technology: Wired
Application: 1000BASE-ZX
Data Transfer Rate: 1Gbps
Wavelength: 1550nm
Max Distance: 80km
Fiber Type: SMF
Connector: Duplex LC
DDM: Without DDM
Operating Temperature: 0~70 °C
Compliant with MSA SFP Specification

We are a international manufacturer and distributor of top quality brand new compatible HP J4860C SFP transceivers, there is a cost-effective modules here and you’ll find our HP J4860C SFP outside your expectation, it’s the one-stop source for optical fiber transceivers the following, just e mail us and tell us the transceivers you need. (More products in: HP SFP)

1000BASE-X Media Components

The following set of media components are used to build a 1000BASE-X fiber optic segment:

1. Fiber optic cable

2. Fiber optic connectors

Gigabit Ethernet fiber optic segments use pulses of laser light instead of electrical currents to send Ethernet signals. This approach has several advantages. For one thing, a fiber optic link segment can carry Gigabit Ethernet signals for considerably longer distances than twisted-pair media can. The standard specifies that a full-duplex 1000BASE-LX segment must be able to reach as far as 5,000 meters (16,404 feet, or a little over 3 miles). However, most vendors sell “long haul” versions of 1000BASE-LX equipment that are designed to reach as far as 10 km (6.2 miles) on single-mode fiber. Vendors have also developed “extended reach” versions of 1000BASE-LX single-mode interfaces that can send signals over distances of 70-100 kilometers or more.

In large, multibuilding campuses, the fiber distances can add up fast, as the fiber cables may not be able to take the most direct route between buildings on the campus and a central switching location. Therefore, these long-reach transceivers can be quite useful. The LX interfaces are essential when it comes to building metropolitan area network(MAN) links, in which Gigabit Ethernet is used to provide network services between sites on a city-wide basis.

Fiber optic cable

Both 1000BASE-SX and 1000BASE-LX fiber optic media segments require two strands of cable: one for transmitting and one for receiving data. The required signal crossover, in which the transmitting and one for reciving data. The required signal crossover, in which the transmit signal (TX) at one end is connected to the receive signal (RX) at the ther end, is performed in the fiber optic link. (Related products in: 10GBASE-LR XFP)

Maximum segment lengths for 1000BASE-SX and 1000BASE-LX are dependent on a number of factors. Fiber optic segment lengths in the Gigabit Ethernet system will vary depending on the cable type and wavelength used.

Fiber optic connectors

The original standard recommended the use of duplex SC fiber optic connectors for both 1000BASE-SX and 1000BASE-LX fiber optic media segments. Figure 1 shows a duplex SC connector. Although the standard can recommend a connector, vendors can use other fiber optic connectors as long as they are not forbidden in the standard. For examle, when the 1000BASE-X media systems first became available, vendors used the compact MT-RJ connector on 1000BASE-SX ports.

21   Figure 1, Duplex SC connector
Figure 2 shows the MT-RJ connector, which provided both fiber connections in a space the size of an RJ45 connector. Because the MT-RJ connector takes up about half the space required by the SC connectors, this allowed vendors to provide more 1000BASE-SX ports on swithch.

22 Figure 2, MT-RJ connector

 

1000BASE-X transceivers

Some vendors used the Gigabit Interface Converter (GBIC), which was an earlier form of transceiver module that allowed the customer to support either the 1000BASE-SX or 1000BASE-LX media types on a single port. The GBIC is a small, hot-swappable module that provides the media system signaling components for a Gigabit Ethernet port.

More recently, vendors have developed a small form-factor pluggable (SFP) transceiver, which can be purchased to support several different kinds of Ethernet fiber optic media systems.

The SFP Transceiver is a small module the plugs into a seitch port and uses a small fiber optic connector called the LC connector. Figure 3 shows the smaller LC fiber optic plug, which is used for connections to SFP fiber optic transceivers.

 

23Figure 3, Duplex LC fiber optic plug